Rubio Monocoat Oil Plus 2C 350ml

Instructions for Furniture, Stairs & Worktops

• STEP 1. Sand the surface scratch-free. Finish with screening net 100 to 150, depending on the sanding method used.
• STEP 2. Vacuum thoroughly and remove any dust residue with Cleaner. Wait until the surface is completely dry (consult the technical data sheet of Cleaner before use).
• STEP 3. Stir the A-component until a homogeneous mixture is obtained. Mix the two components carefully (1 to 2 minutes) with a ratio of about 3 units A to 1 unit B.
• STEP 4. Spread a small amount of Oil Plus 2C with a beige/red Rubio Monocoat Scrubby pad or hand sander with a small beige 5.9 inch Rubio Monocoat pad (you can also use the Rubio Monocoat Mouse Pad for smaller objects and corners).
  • Spatula method: use a stainless steel spatula to spread out the Oil Plus 2C in areas that can be finished in maximum 30 minutes (including step 5).
  • For ceilings and walls, you can use our Rubio Monocoat Brush and Rubio Monocoat beige Scrubby Pad to spread out the oil.
• STEP 5. Let absorb for a few minutes. Wipe away all excess oil with a cloth or hand sander with a small white 5.9 inch Rubio Monocoat pad. Finish off with a cloth within max. 30 minutes. The surface should feel non-sticky! Submerge all used cloths in water.

Instructions for Floors

• STEP 1. Sand the surface scratch-free. Finish with screening net 100.
• STEP 2. Vacuum thoroughly and remove any dust residue with Cleaner. Wait until the surface is completely dry (consult the technical data sheet of Cleaner for use).
• STEP 3. Stir the A-component until a homogeneous mixture is obtained. Mix the two components carefully (1 to 2 minutes) with a ratio of about 3 units A to 1 unit B.
• STEP 4. Work in zones of 5-10 m². Start each zone by treating the borders with a beige or red Rubio Monocoat Scrubby pad. Then apply a small amount of Oil Plus 2C with a brush every 0.5 metres. Spread out per board in the direction of the wood using a polishing machine with a beige or red 16 inch Rubio Monocoat pad.
  • Spatula method: use a stainless steel spatula to spread out the Oil Plus 2C in areas that can be finished in maximum 30 minutes (including steps 5 and 6).
• STEP 5. Remove all excess oil thoroughly with a cloth or a polishing machine with a white 16 inch Rubio Monocoat pad. The surface should feel non-sticky!
• STEP 6. After having finished all areas, go over them again with a new white Rubio Monocoat pad. Now the surface should feel non-sticky. Then immerse all the cloths used in water.

› Instructions for floor repair and renovation

If the surface treated with Oil Plus 2C shows a lot of wear and tear, or needs a colour repair, we recommend maintenance with Oil Plus 2C in the original colour.

• STEP 1. Use Deep Cleaner to make the wooden surface stain-free. Should stains remain, repeat the cleaning process or use one of our stain removers (Grease Remover, Limespot Remover or Tannin Remover). Please consult the technical data sheet before use.
  • If the wooden object is excessively damaged or neglected, you will first need to polish the surface with the same screening grit you used to finish your wooden object initially. If necessary, please consult your professional.
• STEP 2. Remove the dissolved dirt with a damp cloth or mop and clean water and allow the surface to dry well (± 30 minutes at a temperature of 20°C and in a well-ventilated room).
• STEP 3. Stir the A-component until a homogeneous mixture is obtained. Mix the two components carefully (1 to 2 minutes) with a ratio of about 3 units A to 1 unit B.
• STEP 4. Spread out a small amount of Oil Plus 2C with a beige/red Rubio Monocoat Scrubby pad or hand sander with a small beige 5.9 inch Rubio Monocoat pad (you can also use the Rubio Monocoat Mouse Pad for smaller objects and corners).
• STEP 5. Let absorb for a few minutes. Wipe away all excess oil with a cloth or hand sander using a white 5.9 inch Rubio Monocoat pad. Finish off with a cloth within max. 30 minutes. The surface should feel non-sticky! Submerge all used cloths in water.

Tips & Tricks

• The product may not be diluted under any circumstances!
• Stir the product well before applying.
• When using several units on one site, it is recommended to mix them to obtain an even result.
• After application, the surface may appear slightly shiny. This will disappear after 2-3 cleanings with Universal Soap or Surface Care.
• The smoother the surface, the less oil and pigments will penetrate into the wood, resulting in a less coloured surface.
• Our oils are developed with environmentally friendly ingredients. However, some people may be allergic to certain elements. Therefore, we recommend wearing gloves when applying the A+B component in order to protect the skin.

Oil Plus 2C (A)

• Physical state at 20°C: liquid
• Odour: oily
• Flash point: > 100°C
• Density: > 0,9 kg/L
• VOC content: 0 g/L

Accelerator (B)

• Physical state at 20°C: liquid
• Colour: clear
• Odour: odourless
• Flash point: > 160°C (closed)
• VOC content: 0 g/L

Giscode Oil Plus 2C A + B- comp: Ö10/DD+
​

• Preserves the natural look and feel of the wood
• Contains no water or solvents
• Ecological: 0% VOC
• Easy to maintain
• No marks or overlaps
• Durable protection
• Can be used on almost all types and species of wood (solid wood, veneer, MDF, etc.)
• Can be applied on all indoor wooden surfaces (furniture, table tops, stairs, walls, floors, etc.)
• Dries quickly. Can be cleaned starting from at least two days after application with dry maintenance (vacuuming) and from at least five days with water and Universal Soap.
• Can also be applied as renovation or maintenance oil on Rubio Monocoat oiled surfaces
• Suitable for bathrooms and kitchens thanks to its water and heat resistance
• Certificates obtained
  • LCA
  • B-EPD
  • Eurofins Indoor Air Comfort Gold
  • Toy standard EN 71-3
  • Food Contact Compliance
     

• Consumption: 30 - 50 m²/L
• These consumption rates are indicative only. Results depend on the type of wood and the preparation. It is always advisable to apply a sample in order to determine the exact consumption.

• Linseed oil is a natural product and not subject to spontaneous combustion. However, oil on a cloth or other tools does entail a fire risk. The oxidation of the oil leads to heat accumulation, which can result in spontaneous combustion. Therefore, the cloths and other tools must be soaked in water before disposal.
• The product can be stored for 36 months in a dry environment and in the original packaging.
• Oil Plus 2C may be used for a maximum of 4-6 hours after mixing the A & B components.
• Colours serve only as examples. We recommend carrying out a test on identical sanded wood.