Milk Paint Tuscan Red - 946ml

*** 20 May 2021: Section text updated but links still being added ***

Step 1: Preparation for Paint

Before applying paint, all raw wood projects require preparation sanding, and all existing finishes require prep cleaning and sanding. If you skip this critical step, your finish may fail.

Preparation for Raw Wood Projects

See the GF video: How to Prep Sand Raw Wood

1. Sanding schedule: 120-grit sandpaper followed by 150-grit. Do not over-sand with fine-grit sandpapers; this will close and seal the wood grain, preventing ideal color absorption. Do not use steel wool with water-based finishes; the particles will get trapped in the finish and rust.
2. Remove dust with a vacuum, compressed air, an oil-free tack cloth or a water-dampened rag.
3. Let dry completely before applying General Finishes product.

Preparation for Sealed Surface Projects

For high-use areas with heavy grime build-up and oil from hands, give your project a deeper cleaning.
See our video: How to Prepare Existing Finishes

1. Scuff clean with a Scotch Brite™ pad or maroon synthetic steel wool and a 50:50 mix of denatured alcohol and water. Dry 1-2 hours. Avoid cleaning with products containing phosphates (salt), which can linger in the substrate and produce a white haze. If your project requires a deeper cleaning, see Power Prep Cleaning Highly Used Existing Finishes below.
2. Sand lightly with a fine-grade (220-320) foam sanding sponge or 400-grit sandpaper.
3. Remove dust with a vacuum, compressed air, an oil-free tack cloth or a water-dampened rag.
4. Let dry completely before applying General Finishes product.

Power Prep Cleaning Highly Used Existing Finishes

See our video: How to Power Prep Existing High Use Finishes for Stain or Paint

1. Scrub clean with a detergent, such as Spic and Span or Dawn, using a Scotch Brite™ pad.
2. Rinse well with water.
3. Scrub clean with a Scotch Brite™ pad and a 50:50 mix of denatured alcohol and water. Dry 1-2 hours.
4. Sand lightly with a fine-grade (220-320) foam sanding pad.
5. Remove dust with a vacuum, compressed air, an oil-free tack cloth or a water-dampened rag.
6. Let dry completely before applying General Finishes product.

Alternative Cleaning Solutions For Existing Finishes (Not as aggressive or effective as denatured alcohol; requires rinsing.)

1. 50:50 mix of bleach and water
2. 50:50 mix of vinegar and water
3. Mineral spirits can be used when working with water-based products, but only if the surface is thoroughly rinsed and allowed to dry for 72 hours.

Step 2: Priming

A base coat of primer is not required to use General Finishes Milk Paint. However, 2 coats of General Finishes Stain Blocker may be necessary in the following circumstances, especially when using WHITE OR LIGHT-COLORED PAINTS.

Watch Stain Blocker Product Overview video Here

1. RAW WOOD: Before using white & light-colored paints, apply 2 coats of GF Stain Blocker or GF White Undercoat. Raw Wood Tannin Bleed-Through is unpredictable; yellowing can appear immediately or months later with seasonal temperature changes. Oak, pine, mahogany and douglas fir are particularly prone to bleed-through.
2. SEALED SURFACE: Before using white & light-colored paints, apply 2 coats of GF Stain Blocker. Sealed Surface Bleed-Through may be caused by previous stains or aniline dyes, surface contamination, and incompatibility between brands.
3. Knots in Wood contain rosin (sap) and are dense, making paint adhesion a challenge. Pine knots are especially difficult to cover with white or light paints. If you decide to paint over them, apply 3 coats of Stain Blocker over the areas with knots first; however, we cannot guarantee against rosin bleed-through. You are better off using a dark paint on pine.
4. Dark Paint Colors Over Sealed Surfaces: To improve coverage when applying darker colours such as Coastal Blue, Dark Chocolate, or Queenstown Gray, prime with a coat of Lamp Black.
5. Non-Wood Surfaces may be able to take paint if primed first. Primer may improve adhesion over laminate and prevent bleed-through from MDF. Metal requires a primer made specifically for metal.

NOTE: Do not tint Stain Blocker or use Stain Blocker on projects that will be stored outdoors.

Priming Non-Wood Surfaces for Paint

Always test for adhesion on a hidden area of your project before getting started.

Metal: General Finishes Milk Paint is engineered for wood surfaces, but may adhere to metal, such as aluminum or steel, if a metal primer is applied first.

1. Clean surface well.
2. Apply primer.
3. Dry 48-72 hours before painting.

Laminate: Milk Paint MAY adhere to laminate with a bonding primer; however, we cannot guarantee it. You may increase your chances of success by abrading the surface.

1. Prep: Deep clean, dry thoroughly, sand with 150- then 180-grit sandpaper and wipe off dust.
2. Prime: Apply bonding primer, dry 12+ hours before painting.

MDF: Milk Paint can be applied directly to MDF, but the MDF may cast a brown color if not primed first. Two base coats of white-pigmented shellac-based stain-blocking primer, or Stain Blocker, may prevent bleed-through. Alternatively, one base coat of General Finishes Seagull Gray Milk Paint may block brown tone caused by MDF.

MDF is not as absorbent as natural wood. Let each coat of primer and paint dry at least 48 hours before re-coating.

Fiberglass: Milk Paint can be applied directly over fiberglass without primer. We do not recommend applying other General Finishes products over fiberglass. Gel Stain may adhere to fiberglass, but it is not an exterior rated product.

Disclaimer

Although Stain Blocker is engineered to prevent the most persistent bleed-through when two coats are applied, General Finishes cannot guarantee prevention of bleed-through or yellowing on every project. Unknown factors and assiduous bleed-through can impact results. Stain Blocker is the strongest option we are aware of at this time and has performed extremely well in our tests.

Step 3: How To Apply General Finishes Milk Paint

CAUTION: Do NOT use any type of clear topcoat over white or light GF Milk Paint Colours, as it may cause yellowing when used over wood substrates. GF Milk Paint is a premium self-sealing finish and does not require a topcoat. If you want a white paint with a higher sheen, use GF White Poly (spray only) or GF Brushable White Enamel instead. Darker colours can be top-coated if a higher sheen is desired.

Watch our Milk Paint Product Overview Video Here

Watch our How To Achieve A Bright White Finish Here

General Finishes Milk Paint Application Steps

Substrate: Wood (See below for other substrates)

1. Watch product overview video here. 2:18 minutes.
2. Work in a well-ventilated area.
3. Stir paint to reincorporate solids that have settled to the bottom of the can before and throughout the application process.
4. Thin as desired with distilled water; start with 5%, adding up to 10% by volume. Do not use flowing agents such as Floetrol. This paint already contains a flow agent and outside products may not be compatible.
5. Increase open time, if needed, with up to 10-15% General Finishes Extender if allowed by local regulations. GF Extender will improve flow and leveling and increase open time, which is helpful in dry climates.  
6. Apply as many coats as needed for desired coverage. 2-3 coats are standard but additional coats may be required when using colours with less "hide properties," such as bright reds, greens, yellows and whites.
   • Hand application: Using a synthetic bristle brush, foam brush, pad applicator, or microfiber roller such as Whizz or AllPro brand, apply using smooth, even strokes.
   • Spray application: See video tutorial on spraying Milk Paint. Before spraying, strain paint through a medium-mesh filter. Spray wet films at 3-5-mil thickness. HVLP: 1.8mm-2.0mm spray tip, medium air cap. Verify tip sizes with your equipment supplier. See our general guide for spray tip sizes. Keep your gun at a 90° angle, 15 - 20cm from the surface. On large, flat areas, use wet, even patterns 15 - 20cm wide. For narrow surfaces, reduce the fan pattern to 5 - 8cm wide to reduce overspray. Overlap each pass 25% to conceal lines. Wear full filter NIOSH/MSHA-approved respiratory & eye protection. Read here for more information on spraying techniques.
   • Face frames on cabinets: Milk Paint can be applied successfully to cabinet face frames, edges or drawer fronts with a brush, pad or small cabinet-specific roller such as Whizz or AllPro brand.
7. Dry 2+ hours between coats and before General Finishes water-based topcoat in ideal conditions: 20°C/70°F; 50-70% humidity. Be sure to allow adequate dry time. You can tell if a water-based finish is dry if it forms a powder when lightly sanded with a fine-grade (220-320) foam sanding pad. If in doubt, wait longer. Rushing dry time can cause clouding/blush in topcoat due to moisture trapped between coats. Increase dry time if:
   • Humidity is over 80%
   • 3+ coats are applied
   • Thick coats are applied
   • Applying over an existing sealed finish
   • Applying over products from other brands
   • Layering General Finishes water- and oil-based products:
   • Water over oil: Let oil-based products dry 72+hrs before applying water-based products
   • Oil over water: Let water-based products dry 24+hrs before applying oil-based products
   • To accelerate dry time in humid conditions, add General Finishes Accelerator and work in a space with good ventilation and air movement. If you decide to re-coat before the recommended time, test dryness.
8. Finish sand between coats with a fine-grade (220-320) foam sanding sponge or 400-grit sandpaper to improve smoothness and adhesion. Do not use conventional steel wool.
9. Remove dust with a vacuum, compressed air, an oil-free tack cloth or a water-dampened rag.
10. Topcoat is not required but is recommended in certain situations. See "Step 4: Topcoat over Milk Paint" below.

 
Cure Time

Water-based finishes cure and harden for full use after 21 days in ideal conditions. Avoid placing heavy objects on surfaces that have not completely cured. Treat gently, and do not clean with commercial products during the curing period.

Notes on Colour

• All white paints darken or yellow over time, but the change is more evident with bright whites, such as General Finishes Snow White Milk Paint.
• Some colours made in a clear base require additional coats for coverage due to their lower hide quality, e.g., reds, deep blues and yellows. Bright whites may require additional coats over dark existing finishes.

Warning: Do not use water-based products with Linseed Oils or Danish Oils.

Substrates:

The above instructions are for application over wood surfaces only.
Non-wood substrates require different application techniques and dry times. See website FAQs for more information.

With the proper application technique, Milk Paint can adhere well to:

• PVC
• Vinyl
• Fibreglass
• MDF
• Wood

Step 4: Topcoat over Milk Paint

CAUTION: Do NOT use any clear coat over white or light paints such as GF Milk Paint, or GF White Poly as it may cause yellowing. Any clear coat can become reactive over wood substrates, and turn slightly yellow. All of GF's White Paints are self-sealing with high durability and superior water and chemical resistance and do not require a topcoat. If you want a white paint with a higher sheen, use GF White Poly or GF Brushable White Enamel instead.

However, you can topcoat darker colors in high-use surfaces, such as kitchen cabinets or tabletops, with 3 coats of topcoat if you want to increase sheen. Glossier sheens will boost durability and make the surface easier to clean.

Recommendations

General Finishes High Performance Topcoat and General Finishes Enduro Clear Poly dry crystal-clear and are great for darker colours for high-use surfaces. General Finishes Flat Out Flat is our flattest topcoat, only suitable for projects that do not receive major wear.

Topcoating General Finishes Snow White Milk Paint
Clear, water-based finishes can react with wood substrates and previous finishes, causing the topcoat to yellow. This is most evident when using bright white paints. To avoid potential yellowing, use 3 coats of spray-only Enduro White Poly as a standalone finish. See our FAQ: How Do I Prevent Water Based Topcoat or Light Colored Paint from Yellowing?

Creative Finishing Techniques Using Milk Paint

Layering Colors & Distressing

1. Test colors on the underside of your project to ensure it is what you want.
2. Stir the paint. If it is too thick, add a small amount of water to thin, then stir again.
3. Apply 2 coats of base colour using an acrylic bristle brush, poly foam brush, paint pad applicator, or sprayer with an HVLP 1.8 or 2.0 needle.
4. Dy 2-4 hours between coats. Buff each coat with a fine-grade (220-320) foam sanding pad or 400-grit sandpaper.
5. Apply 2 coats of top color. Dry 2-4 hours between coats, but no more than 4 hours; sanding is easier when the paint has had less time to tighten down. Buff each coat as before with a fine-grade (220-320) foam sanding pad or 400-grit sandpaper.
6. TIP: If you want more of the underlying color exposed, seal the base color with a coat of General Finishes High Performance Topcoat before painting the top color. This allows for easier sanding without burning all the way through to bare wood.
7. Using 120- to 150-grit sandpaper, sand through the top color to reveal the base colour.

Chippy Farmhouse Technique

MATERIALS NEEDED:

• General Finishes Water Based Wood Stain: Espresso
• General Finishes Milk Paint: Snow White
• Water-Based Topcoat
• Assorted Foam & Chip Brushes
• Vaseline
• Paper Towels

STEPS:

1. Stain raw wood with Espresso Water Based Wood Stain.
2. Paint or dab Vaseline in random areas.
3. Paint over Vaseline with Snow White Milk Paint. Let dry.
4. Wipe back with a paper towel to reveal chipped areas (repeat with different colors for layered, aged effect).
5. Seal with 3 coats of water based topcoat.

Creating Custom Colours

You can design your own custom glazes, stains, washes and varnishes with General Finishes intermixable water-based products. See tips and recipes below:

For the mixes listed below, General Finishes recommends the following two steps:

1. Applying a base layer of High Performance Topcoat before applying your custom glaze.
2. Protect all of these finishes with 2-3 coats of topcoat when you are finished.

Pastel Glaze/Whitewash:

MATERIALS NEEDED:

• General Finishes Milk Paint: Your choice of colors
• General Finishes Glaze Effects: Winter White OR General Finishes Water Based Wood Stain: Whitewash

Do not add more than 50% paint to the glaze or stain, or else there will be so much pigment it will be difficult to wipe away the finish.

Custom Glaze:

MATERIALS NEEDED:

• General Finishes Glaze Effects: Your choice of colors

SAMPLE MIX:

Pitch Black Glaze Effects + Winter White Glaze Effects.

Experiment with proportions and colors.

Custom Stain Colors:

MATERIALS NEEDED:

• General Finishes Milk Paint: Your choice of color
• General Finishes Glaze Effects: Clear Base OR General Finishes Pre-Stain Wood Conditioner Natural

SAMPLE MIXES:

• 1 part Milk Paint + 1 part Pre-Stain Natural [50:50 mix] OR
• 1 part Milk Paint + 1 part Glaze Effects Clear Base [50:50 mix] OR
• 1 part Milk Paint +  2 parts Water Based Wood Stain Natural [1:2 mix]

Proportions are relative to the color you are reducing. Some colors may require 2 parts Clear Base to reduce strength, others may require 1.

Begin with a 50:50 mix, and add more Clear Base as needed.

Increase your color palette by mixing 2 or 3 Milk Paint colors together before adding the Clear Base.

See Milk Paint & Glaze Effects Samples

Cleanup of Water Based Products

Application tools and materials containing water-based products can be cleaned with soap and water immediately after use.

Product Spills
Spills may be able to be removed from fabric and carpet if cleaned immediately with soap and water.

Storage of Water-Based Products

Please be mindful of the manner in which water-based products are stored and how long they have been in storage. 
 

Life of Product
Water-based products do not last forever, even when unopened. However, the life of the product may be extended with proper care and storage (see Storage Tips below).

Water-based products can last 3-5 years if the can is unopened, in good condition and stored in correct temperatures.

Product that is 3 years old will not look like product that is 6 months to 1 year old. You will see more stratification or separation as the product ages. Always stir thoroughly before using. 

Foul Smell
If your product has a foul smell, it is contaminated and no longer in useable condition.

Clumps & Settling
Gravity can cause some solids to settle on the bottom of the can and slight separation on the top. This is normal. If working with older product stir with a paint mixing attachment on a drill.

If the solids dissolve and clumps smooth out after mixing from the bottom, the product is in good condition for use.

Inability to reincorporate large, chunky lumps after stirring for several minutes is an indication that the product has frozen and can no longer be used.

Storage Tips
Water-based finishes crystalise and form a skin due to evaporation when the air-tight seal on a can is broken at first use. The following best practices will increase the life of your product:

1. Pry open sealed lids with a paint can opener by hooking under the lid's rolled edge. The use of a screwdriver can disfigure the rim and lid, impairing a complete seal. 
2. Keep lid closed while working. Pour what you will use into a bowl, paper cup, or plate, and close can lid as you work.
3. Clean the chime of the can thoroughly with a paper towel before closing to create a complete seal. Product falling into the chime can be minimized by using a pouring lid, such as Fitsall. Avoid wiping used brushes on the lid.
4. Pound the lid in place using a rubber mallet to avoid distorting the chime or lid. Dents in the lid from direct contact with a hammer can impair a complete seal. Alternatively, place a flat piece of wood over can lid and firmly pound shut.
5. Store in moderate temperatures. Avoid temperatures below 10°C or above 26°C. Keep from freezing. Frozen and heat-damaged product cannot be revitalised. Temperature-controlled spaces, such as a basement, are ideal for storage. Do not store product in an attic, garage, in direct sunlight, or next to something warm like a water heater or furnace.
6. Store can upside down to create a liquid seal, minimize evaporation and reduce the chance of crystallization. Decant remaining product from the can before stirring. 
7. Decant leftovers to a smaller container when the finish is almost used up. Alternative storage containers for water-based products are plastic FIFO bottles or glass bottles. Do not fill metal-lidded containers completely to prevent them from rusting.

The following water-based product mixtures can be stored:

1. Product thinned with up to 15% General Finishes Extender or General Finishes Accelerator can be stored, with the exception of thinned General Finishes Water Based Wood Stain.
2. Mixtures involving colours & sheens within the same product line, such as:
   • High Performance Satin + High Performance Gloss
   • Snow White Milk Paint + Coastal Blue Milk Paint
   • Amber Dye Stain + Merlot Dye Stain

The following product mixtures should NOT be stored:

• Any water based product with thinned tap water; water often contains bacteria that will adversely affect stored paint.
• Topcoat + Stain or Paint
• Milk Paint + Chalk Style Paint
• Water Based Wood Stain + Dye Stain

Furniture Care and Maintenance

Cure First
You have just finished applying a fine furniture finish. Treat gently until the paint or topcoat have fully cured. Allow 21 days for a water-based finish to cure before cleaning.

Regular Cleaning and Maintenance

• Remove dust with a water-dampened cloth. Dust can build up over time and may scratch or dull finishes if not removed regularly. 
• Remove fingerprints, cooking fumes and smoking residue with mild soap and water. These contaminants will not harm the finish, but they accumulate on surfaces and dull the original lustre. 
• As with all fine furniture finishes, avoid using furniture polish, cleaners or dusting sprays that contain silicone, alcohol, ammonia and anything acidic. Exception: We have successfully cleaned with Clorox wipes.
• Clean up water, alcohol and food spills in a timely manner and use placemats & coasters to protect the finish.
• Future finishes or touch-ups may not adhere properly or perform as desired over a contaminated surface. Some contaminants, such as silicone, seep through finish into the wood and often cannot be removed.
• Avoid excessive exposure to direct sunlight, high temperatures or high humidity. These can damage furniture and finishes.

Milk Paint Bases

Technical Data Sheet (TDS)

Milk Paint - 2019-04

Safety Data Sheet (SDS)

Milk Paint: Alabaster - 2018-11
Milk Paint: Antique White - 2018-11
Milk Paint: Ballet Pink - 2018-11
Milk Paint: Basil - 2018-11
Milk Paint: Blue Moon - 2018-11
Milk Paint: China Blue - 2018-11
Milk Paint: Clear Base - 2016-09
Milk Paint: Coastal Blue - 2018-11
Milk Paint: Coral Crush - 2018-11
Milk Paint: Dark Chocolate - 2018-11
Milk Paint: Driftwood - 2018-11
Milk Paint: Emerald - 2018-11
Milk Paint: Empire Gray - 2018-11
Milk Paint: Gulf Stream Blue - 2018-11
Milk Paint: Halcyon Blue - 2018-11
Milk Paint: Harvest Yellow - 2018-11
Milk Paint: Holiday Red - 2018-11
Milk Paint: Key West Blue - 2018-11
Milk Paint: Klein Blue - 2018-11
Milk Paint: Lamp Black - 2018-11
Milk Paint: Linen - 2018-11
Milk Paint: Millstone - 2018-11
Milk Paint: Patina Green - 2018-11
Milk Paint: Perfect Gray - 2018-11
Milk Paint: Persian Blue - 2018-11
Milk Paint: Persimmon - 2018-11
Milk Paint: Queenstown Gray - 2018-11
Milk Paint: Reverent Gray - 2018-11
Milk Paint: Seagull Gray - 2018-11
Milk Paint: Snow White | White Base - 2018-01
Milk Paint: Sunglow - 2018-11
Milk Paint: Tuscan Red - 2018-11
Milk Paint: Twilight - 2018-11
Milk Paint: Westminster Green - 2018-11

Colours

End of Line Colours
 

Product Brochures

Brochure: Milk Paint: Retail - 2019

Brochure: Milk Paint: Signature - 2019